Kampinis šlifuoklis | greičio reguliavimas | 1400W | 125 mm (YT-82099) (Kodas: YT-82099)
Prekių nuotraukos skirtos tik iliustraciniams tikslams, originalių produktų spalvos, užrašai, parametrai, matmenys, dydžiai, funkcijos, ir/ar bet kurios kitos savybės dėl savo vizualinių ypatybių gali atrodyti kitaip negu realybėje, todėl prašome vadovautis prekių savybėmis, kurios nurodytos prekių aprašymuose. Kilus klausimams, visada laukiame Jūsų skambučio telefonu +370 650 61061 arba el. paštu info@drdtools.lt.
Gamintojas: Yato
Mark
Yato
Symbol
YT-82099
Series
GRE
Application
cutting stainless steel, grinding welds, grinding concrete with a cup wheel
Kit contents
angle grinder, additional handle, abrasive wheel guard, key for fastening the abrasive wheel
Turnover
3000-12000 min⁻¹
Mass
2 kg
Tension
230-240Vac
Power
1400W
Cable length
3 m
Level of security
IPX0
Frequency
50 Hz
Electrical insulation class
II
sound pressure
89.3 ± 3.0dB(A)
Acoustic power
100.3 ± 3.0dB(A)
Electronically adjustable speed
Yes
Vibrations
6.95 ± 1.5 m/s²
Grinding wheel diameter
125mm
Abrasive wheel bore diameter
22mm
Spindle thread size
M14
Very powerful and at the same time handy angle grinder with speed control. The copper windings of the rotor and stator are double insulated with a flexible varnish that does not chip off when exposed to high temperatures, protecting the motor from damage. The machine has a soft start system to protect the toothed gear. It also has a built-in low-speed constant speed function, making stainless steel grinding work with the flap disc efficient and without damaging the machine. The slim housing provides a comfortable grip even during long-term operation for the safety and comfort of the operator. Spare brushes are included in the set, and their replacement does not require dismantling the whole machine, but only removing its rear part (part of the housing in black). The bevel gear is precisely fitted and made of steel with a hardness of 53-56 HRC and has a high torque. Speed regulation in the range of 3000-12000 rpm is based on an electronic system that allows automatic selection of power from the network in the case of work with strong pressure at low / medium speed: inox steel, grinding welds or grinding concrete with a cup wheel. The grinder allows you to cut steel elements and reinforced concrete or stoneware much faster than devices with lower power and is less susceptible to wedging the disc in the material. The device is designed for grinding work thanks to the rear handle and the switch located right next to the handle. This construction makes it easier to exert pressure on the machine and does not cause operator fatigue even when sanding large surfaces.
Yato
Symbol
YT-82099
Series
GRE
Application
cutting stainless steel, grinding welds, grinding concrete with a cup wheel
Kit contents
angle grinder, additional handle, abrasive wheel guard, key for fastening the abrasive wheel
Turnover
3000-12000 min⁻¹
Mass
2 kg
Tension
230-240Vac
Power
1400W
Cable length
3 m
Level of security
IPX0
Frequency
50 Hz
Electrical insulation class
II
sound pressure
89.3 ± 3.0dB(A)
Acoustic power
100.3 ± 3.0dB(A)
Electronically adjustable speed
Yes
Vibrations
6.95 ± 1.5 m/s²
Grinding wheel diameter
125mm
Abrasive wheel bore diameter
22mm
Spindle thread size
M14
Very powerful and at the same time handy angle grinder with speed control. The copper windings of the rotor and stator are double insulated with a flexible varnish that does not chip off when exposed to high temperatures, protecting the motor from damage. The machine has a soft start system to protect the toothed gear. It also has a built-in low-speed constant speed function, making stainless steel grinding work with the flap disc efficient and without damaging the machine. The slim housing provides a comfortable grip even during long-term operation for the safety and comfort of the operator. Spare brushes are included in the set, and their replacement does not require dismantling the whole machine, but only removing its rear part (part of the housing in black). The bevel gear is precisely fitted and made of steel with a hardness of 53-56 HRC and has a high torque. Speed regulation in the range of 3000-12000 rpm is based on an electronic system that allows automatic selection of power from the network in the case of work with strong pressure at low / medium speed: inox steel, grinding welds or grinding concrete with a cup wheel. The grinder allows you to cut steel elements and reinforced concrete or stoneware much faster than devices with lower power and is less susceptible to wedging the disc in the material. The device is designed for grinding work thanks to the rear handle and the switch located right next to the handle. This construction makes it easier to exert pressure on the machine and does not cause operator fatigue even when sanding large surfaces.