Pneumatinis smūginis veržliasukis | 20 mm (3/4") | 1300 Nm (YT-09564) (Kodas: YT-09564)
Prekių nuotraukos skirtos tik iliustraciniams tikslams, originalių produktų spalvos, užrašai, parametrai, matmenys, dydžiai, funkcijos, ir/ar bet kurios kitos savybės dėl savo vizualinių ypatybių gali atrodyti kitaip negu realybėje, todėl prašome vadovautis prekių savybėmis, kurios nurodytos prekių aprašymuose. Kilus klausimams, visada laukiame Jūsų skambučio telefonu +370 650 61061 arba el. paštu info@drdtools.lt.
Gamintojas: Yato
Mark
Yato
Symbol
YT-09564
Series
GRF
Application
industry, mechanical workshops, car services
Turnover
5000 min⁻¹
Max torque
1300 Nm
Type of tool holder
driver
Quick connector size
3/8" (9.5 mm)
Type of impact mechanism
TWIN HAMMER
Rotation direction switch
Yes
Tool holder size
3/4" (19.0 mm)
Recommended working pressure
0.63 MPa
Max. working pressure
0.6-0.8 MPa
Required air flow
660 l/min
Inner diameter of the air supply hose
3/8" (9.5 mm)
Air connection diameter (PT)
3/8" (9.5 mm)
Mass
4.7kg
Length
230mm
Housing material
aluminum
Set contents
pneumatic wrench, hose connector
Sound pressure
92.0 ± 3.0 dB(A)
Acoustic power
103.0 ± 3.0 dB(A)
Vibrations
5.47 ± 1.5 m/s² Pneumatic wrench 3/4" 1300 Nm Professional pneumatic wrench by YATO. Drive size 3/4". Maximum power achieved at a pressure of 6 BAR is 1300 Nm. How to use: Before each use of the tool, make sure that no element of the pneumatic system is damaged. If any damage is observed, the system components should be immediately replaced with new, undamaged components. Before each use of the pneumatic system, dry any moisture condensed inside the tool, compressor and hoses. Before starting work, attach the additional handle with four screws. Connecting the tool to the pneumatic system: the drawing shows the recommended method of connecting the tool to the pneumatic system. The method shown will ensure the most efficient use of the tool and will also extend the life of the tool
put a few drops of SAE 10 viscosity oil into the air intake
firmly and securely screw the appropriate end to the air inlet thread to connect the air supply hose (II)
attach the appropriate tip to the tool carrier; When working with pneumatic tools, use only equipment adapted to work with impact tools
set the appropriate direction of rotation (V); the direction of rotation is marked with an arrow; adjust pressure (torque)
connect the tool to the pneumatic system using a hose with an internal diameter of 1/2". make sure that the strength of the hose is at least 1.38 MPa (III)
run the tool for a few seconds making sure there are no suspicious sounds or vibrations coming from it
Working with impact socket wrenches: Before starting to tighten a bolt or nut with a wrench, manually screw the bolt or nut onto the thread (at least two turns). Make sure that the socket wrench size is correctly selected for the element to be unscrewed or tightened. Incorrect selection of sizes may result in the destruction of both the wrench and the nut or bolt. The thread diameter of the screw to be tightened cannot exceed 21 mm. Unscrewing and tightening: adjust the pressure in the pneumatic system so that it does not exceed the maximum value for the given tool
set the appropriate direction of rotation of the tool and the appropriate torque (V)
install the appropriate socket wrench (IV) on the tool carrier
connect the wrench to the pneumatic system
place the wrench with the attached socket on the element to be unscrewed or tightened
gradually press the tool trigger
After finishing work, dismantle the pneumatic system and preserve the tool
Contents of the package: The wrench is equipped with a connector allowing it to be connected to the pneumatic system. Technical data: unit: No
pressure [bar]: 6.3
torque [Nm]: 1300
min/max revolutions: 5000
packaging: color box
quick connector size [inch]: 3/8"
spindle size [mm]: 3/4"
efficiency [l/min]: 660
size [inch]: 3/4"
Yato
Symbol
YT-09564
Series
GRF
Application
industry, mechanical workshops, car services
Turnover
5000 min⁻¹
Max torque
1300 Nm
Type of tool holder
driver
Quick connector size
3/8" (9.5 mm)
Type of impact mechanism
TWIN HAMMER
Rotation direction switch
Yes
Tool holder size
3/4" (19.0 mm)
Recommended working pressure
0.63 MPa
Max. working pressure
0.6-0.8 MPa
Required air flow
660 l/min
Inner diameter of the air supply hose
3/8" (9.5 mm)
Air connection diameter (PT)
3/8" (9.5 mm)
Mass
4.7kg
Length
230mm
Housing material
aluminum
Set contents
pneumatic wrench, hose connector
Sound pressure
92.0 ± 3.0 dB(A)
Acoustic power
103.0 ± 3.0 dB(A)
Vibrations
5.47 ± 1.5 m/s² Pneumatic wrench 3/4" 1300 Nm Professional pneumatic wrench by YATO. Drive size 3/4". Maximum power achieved at a pressure of 6 BAR is 1300 Nm. How to use: Before each use of the tool, make sure that no element of the pneumatic system is damaged. If any damage is observed, the system components should be immediately replaced with new, undamaged components. Before each use of the pneumatic system, dry any moisture condensed inside the tool, compressor and hoses. Before starting work, attach the additional handle with four screws. Connecting the tool to the pneumatic system: the drawing shows the recommended method of connecting the tool to the pneumatic system. The method shown will ensure the most efficient use of the tool and will also extend the life of the tool
put a few drops of SAE 10 viscosity oil into the air intake
firmly and securely screw the appropriate end to the air inlet thread to connect the air supply hose (II)
attach the appropriate tip to the tool carrier; When working with pneumatic tools, use only equipment adapted to work with impact tools
set the appropriate direction of rotation (V); the direction of rotation is marked with an arrow; adjust pressure (torque)
connect the tool to the pneumatic system using a hose with an internal diameter of 1/2". make sure that the strength of the hose is at least 1.38 MPa (III)
run the tool for a few seconds making sure there are no suspicious sounds or vibrations coming from it
Working with impact socket wrenches: Before starting to tighten a bolt or nut with a wrench, manually screw the bolt or nut onto the thread (at least two turns). Make sure that the socket wrench size is correctly selected for the element to be unscrewed or tightened. Incorrect selection of sizes may result in the destruction of both the wrench and the nut or bolt. The thread diameter of the screw to be tightened cannot exceed 21 mm. Unscrewing and tightening: adjust the pressure in the pneumatic system so that it does not exceed the maximum value for the given tool
set the appropriate direction of rotation of the tool and the appropriate torque (V)
install the appropriate socket wrench (IV) on the tool carrier
connect the wrench to the pneumatic system
place the wrench with the attached socket on the element to be unscrewed or tightened
gradually press the tool trigger
After finishing work, dismantle the pneumatic system and preserve the tool
Contents of the package: The wrench is equipped with a connector allowing it to be connected to the pneumatic system. Technical data: unit: No
pressure [bar]: 6.3
torque [Nm]: 1300
min/max revolutions: 5000
packaging: color box
quick connector size [inch]: 3/8"
spindle size [mm]: 3/4"
efficiency [l/min]: 660
size [inch]: 3/4"